Doktek Technology
ADDRESS: Merkezefendi / Denizli, Türkiye
Machines made in Türkiye
EN

Doktek Technology · November 19, 2026

The choice between fiber laser and plasma starts with the parts you make most often. A workshop producing small holes and clean edges in thin sheet has different priorities from a fabricator cutting large structural parts from thick plate. Both processes cut metal; weigh thickness, dimensional tolerances, production volume and the work that follows cutting together.

Our 12 × 3 m single-table fiber laser cutting thick plate

How do the two processes work?

A fiber laser focuses a beam delivered through an optical fiber onto a small spot. The metal melts at that point, and assist gas removes the molten material from the kerf. With the focus, gas and speed set correctly, the process produces a narrow kerf and detailed contours.

Plasma cutting uses an electric arc to ionise gas. The hot plasma jet melts electrically conductive metal and removes it from the cut. Results depend on the torch, consumables, height control and motion system as well as the power supply. Standard plasma and high-definition plasma do not deliver the same quality, so identify the equipment class being compared.

Fiber laser and plasma comparison table

CriterionFiber laserPlasma
Cut quality and kerfGenerally a narrower kerf, with an advantage on fine detailsTypically a wider kerf; quality depends on the system
Dimensional accuracyGenerally advantageous for tight-tolerance partsMay suit structural work; system class matters
Heat-affected zoneGenerally narrower, though thermal effects remainTypically wider; settings and speed affect it
Edge angularityGenerally lower with correct settingsCan be more pronounced; advanced systems reduce it
Thin and medium sheetA strong option for precise, detailed partsWorth considering for simple contours and suitable tolerances
Very thick plateAssess power, gas and target quality togetherCan be economical and practical with a suitable system
Small-hole qualityGenerally better; diameter relative to thickness mattersRisk of taper and dross; dedicated hole processes improve results
Speed on thin sheetGenerally higher cutting speedMay be disadvantaged on small, complex contours
Consumables and running costsCount nozzles, protective windows, gas and energy togetherInclude electrodes, nozzles, gas and cleanup labour
GasOxygen, nitrogen or suitable compressed air, depending on materialAir or other gases, depending on system and metal
AutomationCan integrate CNC, nesting and loading solutionsCan cut automatically with CNC and height control
Initial investmentGenerally higher; power and equipment affect itGenerally lower; advanced equipment can narrow the gap

The table describes general industry trends, rather than measured results from a particular machine. Have the same material and drawing cut on both systems, then compare edges, holes, dross and dimensions.

When does plasma still make sense?

Plasma is a strong candidate when most production involves very thick plate and large parts with simple geometry. Rough preparation before welding, or parts that will be machined afterwards, may not need the fine detail a laser offers. A suitable plasma system may then meet the requirement with a lower initial investment.

A workshop with a limited budget, modest cutting volume or broad tolerances can also consider plasma. Balance the lower investment against time spent grinding, correcting holes and machining. High-definition plasma can deliver good results; assuming that every plasma cut will be rough is misleading too.

When does fiber laser stand out?

Fiber laser generally has an advantage for interlocking parts, small holes, narrow slots and closely spaced contours in thin and medium sheet. Its narrow kerf helps preserve fine features. With suitable settings, less dross and edge correction can shorten the production steps that follow cutting.

For stainless steel and aluminium parts requiring good visible edges or delivery close to assembly condition, assess fiber laser together with the gas choice. Nitrogen is a common option when an oxide-free edge is needed, but the required finish, alloy and thickness must be tested. Every hole may not emerge at its finished size; very tight tolerances can require a machining allowance.

Thickness does not decide the choice by itself

Restricting fiber laser to thin sheet overlooks modern high-power machines. Doktek’s 20 kW machine with a 12 × 3 m bed cuts mild steel up to 60 mm thick using oxygen. This is a cutting capability of our own machine; it does not mean every part at that thickness will be produced at the same speed and quality.

Assess maximum cutting thickness separately from the quality and productivity required in continuous production. Piercing, corners, small holes and unloading time affect the overall result. Request trials with your actual work before agreeing the configuration.

Total cost: gas, consumables and automation

Calculate cost per accepted part. Include electricity, gas, consumables, operator time, maintenance and scrap, together with downstream work such as grinding and hole correction. Fast cutting and limited rework may favour laser on thin sheet; plasma may provide a better balance on thick, simple work.

In laser cutting, oxygen supports the cutting reaction in mild steel; nitrogen expels the melt while limiting oxidation. Compressed-air cutting requires attention to dryness, oil contamination and filtration. Plasma gas requirements also vary with the metal and torch system. Avoid treating any gas as the cheapest choice for every job.

Both processes can cut automatically with CNC. Nesting software, loading, unloading and the operator’s part-sorting time determine daily output. A laser’s high cutting speed does not translate into the same production gain if it waits for loading. Include extraction, protection, gas supply, floor space and servicing in the investment comparison.

Checklist before making a decision

  • List your most frequent materials and thicknesses; assess occasional thick-plate work separately.
  • Specify drawing tolerances, the smallest hole and the required edge condition.
  • Have typical parts cut with both processes; inspect top and bottom faces, angularity and assembly fit.
  • Add loading, piercing, part sorting and finishing to the cutting time.
  • Compare gas, consumables, maintenance and labour per accepted part.
  • Plan floor space, electrical and gas supplies, extraction and operator training.

For a mixed workload, it may make more sense to plan frequent precision parts separately from occasional heavy work, rather than forcing every job onto one machine. Base the investment on your everyday order mix, rather than a single demonstration cut.

Define the right configuration with Doktek

Doktek Technology offers open-type and enclosed fiber laser cutting machines as well as tube laser solutions. Choosing an open frame or an enclosure is a separate decision from choosing the cutting process: consider access, protection, fume control and production layout together. Tube and profile work also has different clamping and motion requirements from flat-sheet cutting.

Share your material, typical thicknesses, required bed size and sample drawings. We can assess your cut-quality expectations and downstream operations together, then define suitable power, gas and machine construction for your work.

FAQs

YOUR QUESTIONS ANSWERED

Is plasma always better for thick plate?

No. It can make sense for very thick, simple parts, while high-power fiber laser can also cut thick plate. Assess material, target quality, hole geometry and total part cost together.

Which process suits stainless steel and aluminium?

Fiber laser generally stands out for precision parts and clean edges. Confirm gas, power and alloy performance through samples; suitable plasma systems can cut these metals too.

Does fiber laser have an advantage on small holes?

Generally, yes. The narrow kerf helps with fine features, but hole diameter, sheet thickness and tolerances still matter. Advanced plasma hole processes can also improve quality.

Which has lower running costs?

It depends on the work. Include cutting speed, scrap, maintenance and finishing labour alongside gas and consumables. Compare cost per accepted part.

Does switching from plasma to laser eliminate grinding?

Not on every job. Correct laser settings can reduce dross and rework; thickness, oxide layers and subsequent painting or welding may still require cleaning.

Knowledge center

MORE ARTICLES

Get a quote for your machine. Tell us what you need, and we'll work with you to define the right configuration.